How To Repair Light Pull Chain On Hunter Ceiling Fan

Download Commodity

Download Commodity

If your ceiling fan pull chain is cleaved because it was pulled out of the switch, at that place's an easy way to set up it. Open the switch in the ceiling fan and remove the broken piece of concatenation before replacing it with a longer one. If your switch is completely broken, buy a replacement at a local hardware store before removing the old one and installing the new switch. Brand sure y'all plough the ability source off before taking apart the ceiling fan to exist safe.

1. 1

   Turn the power off at the excursion breaker for safety. Locate your circuit breaker, likely either in the basement, a closet, or even exterior the house. Open the circuit breaker and turn the power off for the room where you'll be working with the ceiling fan to brand sure electricity isn't yet flowing when you lot're removing the fan'due south parts.^[1]

   • If yous're non certain which switch is for the room with the ceiling fan, turn off the main power merely to be safe.

2. ii

   Remove the lite bulbs to prevent them from breaking. Set upward a ladder or stride stool if necessary to reach the ceiling fan easily. Unscrew the light bulbs carefully and place them on a towel nearby. If the ceiling fan has any sconces or globes, remove these as well by unscrewing them or using a screwdriver to remove whatsoever screws.^[2]

   Advertisement

3. iii

   Use a screwdriver to remove the screws property the light fixture in place. The ceiling fan'due south fixture, or the main housing where the wiring is stored, will be held together with a few visible screws. Use a screwdriver to take out these screws, loosening the fixture to see the wiring and switch.^[three]

   • Set up the screws and detachable fixture slice aside in a rubber place to reattach them afterward.

4. 4

   Unscrew the nut on the side of the fixture that holds the switch. Await on the exterior of the fixture for a small nut. Unscrew this nut to remove information technology completely, letting you access the ceiling fan pull chain switch. Set the nut aside for safekeeping.^[4]

5. five

   Pull out the switch to inspect the concatenation more than closely. Now that the switch is loosened from the fixture, look at it upwardly close. If the wiring of the switch is broken, replace it completely. Leverage the switch open using a screwdriver to encounter if the chain simply needs to exist replaced with a longer slice, or if it would be best to get a new switch all together.^[5]

   • If the chain looks replaceable, use a longer length of concatenation yous already take to set it instead of purchasing another 1.
   • If the switch looks cleaved, visit a local hardware store to buy a replacement.

   Advertisement

1. 1

   Popular open up the switch using a small screwdriver. Leverage open the tabs forth the switch using a screwdriver. Once you lot separate it into its ii pieces, the things inside of information technology, like the chain and spring, volition be visible. With the switch open, remove it from the wiring by pulling the wires out from the switch.^[vi]

   • Be careful not to lose any of the pieces when you pop the switch open.
   • If you don't see the spring and chain, pop off the protective plate belongings them inside the switch.

2. 2

   Remove the cleaved slice of chain from the mechanism. Remove the contents of the switch, including the cleaved piece of chain continued to a disc and the spring. All of the contents inside the switch will be loose, making it piece of cake to only take them out. Popular the broken chain off of the disc using a screwdriver. Discard the broken chain afterwards you've removed information technology.^[seven]

3. 3

   Put a longer piece of concatenation in the former concatenation'due south spot. Just as you removed the curt cleaved chain, pop a longer chain that will reach through the fixture into place in the old chain'due south spot. Snap the longer concatenation into the disc where the broken chain was using your fingers.^[8]

4. iv

   Reassemble the switch by putting the chain and spring dorsum into identify. Put the spring and chain attached to the disc back into the switch. Pull the chain through the pigsty in the switch and so you lot can pull on it easily. If you popped off a protective plate that holds everything together, press this dorsum into place too.^[nine]

   • Agree downwards the leap and chain mechanism using your finger or a screwdriver then it doesn't popular up while you lot're attaching the 2 principal switch pieces together.
   • The two switch halves will press back into each other hands.

5. v

   Place the switch dorsum inside the fixture and reattach the switch nut. Put the switch dorsum in the wires just as you took information technology out. Make certain you place the switch adjacent to the spot where you lot unscrewed the nut from the outside of the fixture. Spiral the nut back into identify to hold the switch.^[10]

   Advertisement

1. ane

   Purchase a replacement switch at your local home comeback store. Either take a moving-picture show of your old switch and so you know which one to buy, or disassemble the erstwhile switch and take it with you. Wait for a "fan light switch" or something labeled similarly.^[11]

   • Ask an employee at the home improvement or hardware store for help if y'all're not sure which switch to buy.

2. two

   Disconnect the wires attached to the old switch. Pulling or twisting off the connectors that agree together the wires will disconnect them from the former switch. Remove each wire that'due south fastened to the old switch past pulling off the connectors, and have the former switch out.^[12]

   • Take a picture of which wires are connected to the switch before disassembling it to reference the picture when putting it dorsum together.

3. 3

   Strip 0.5–0.75 in (1.3–i.9 cm) of insulation off of the wires to attach them. Use a wire stripper to strip the insulation off of the ends of the wires attached to the new switch, cutting into the insulation with the stripper before pulling it towards the finish of the wire to remove it. This will allow the electrical connexion to pass through the wires.^[13]

4. four

   Twist the wires together and cover them with connectors. Locate the quondam wires that your new wires will attach to and twist them together tightly using a clockwise motion. Many wires are color-coded, making it like shooting fish in a barrel to friction match the correct wires together. Cover the blank wire with a twist-on connector, making sure the entire bare wire is covered.^[fourteen]

   • Refer to the picture you lot took of the wires the old switch connected to, if needed.
   • Twist-on connectors are likewise called wire basics and can be found at your local hardware store.

5. 5

   Put the new switch into the fan housing to reattach the nut on the outside. Since y'all removed the minor nut on the outside of the fixture that holds the switch in place before, it's fourth dimension to reattach it. Concur the switch inside the fixture, and screw the nut dorsum on to the outside of the fixture to concord the switch in place.^[15]

   Advertisement

1. 1

   Agree the fixture over the wiring and screw it back into place. With your switch replaced, identify the role of the fixture that you removed back into identify on top of the wiring. Hold it steady and apply the screws to screw it back in using a screwdriver.^[16]

   • Ask someone to agree the fixture in place while you screw the screws back in, if desired.

2. 2

   Put the lightbulbs dorsum into the fixture if needed. If you removed any globes or sconces that went around the bulbs, reattach these first either by twisting them back on or using a screwdriver to reinstall the screws. Pick up the lightbulbs and advisedly twist each one back into place in the fixture.^[17]

3. 3

   Plough the ability back on through the breaker. Return to the excursion breaker and flip the switch that turns dorsum on the ability. If your circuit breaker isn't labeled, make sure you turned the right power back on by testing the light switch in the ceiling fan room.^[18]

4. 4

   Examination the pull chain to run across if it works. Flip the power switch in the room if necessary to plough the fan on. Now that your ceiling fan pull chain switch is fully installed, pull on information technology gently to run across if it works. If the lights come on or the fan starts to rotate, it'due south all fixed.^[19]

   • Avoid pulling on the concatenation using a lot of force considering this is often how it breaks.

   Advertisement

Add together New Question

• Question

  If the chain just came off in my hand do I take to buy a new switch or can I only put the concatenation dorsum on?

  

  This happened to me 3 days ago. I had to purchase a new 3-speed ceiling fan switch every bit the concatenation that bankrupt will Not go back in the switch. You'll demand a large paper prune to get the wires in the terminal every bit per the directions that came with the one I bought from Lowe'southward.

• Question

  How do I know if the fan switch is working?

  

  You will need a ability tester with a light. Cheque each concluding for power with the switch on and off -- if it lights upwardly when you turn the switch on, information technology is a good switch.

• Question

  We want to connect a 3-speed wall switch to replace the chain-pull switch on our ceiling fan. At some point there was a switch for a calorie-free, which was removed. There are 4 black wires inside the wall with wire nuts on them. The new 3-speed switch has 2 black wires. How can we tell what nosotros are supposed to connect?

  

  ii of the wires were for the light and 2 for the fan. You volition demand a voltage tester light to meet which ones are power, unless 2 or 3 of the black wires are wired together, then those would be the power and the other blackness wires would be for the fan or low-cal.

• Question

  My pull chain is threaded through the threaded stock that holds the light comprehend on, where is the switch? How do I become to it?

  

  Kickoff, plough off the breaker or fuse for this electrical area. Remove the calorie-free cover. Look for screws that hold the light plate in. Keep 1 hand below the plate and hold onto it every bit yous unscrew the screws. Mitt the screws to someone, or drib into a pants' pocket. The unit you are looking for volition be inside the housing.

Ask a Question

200 characters left

Include your e-mail address to go a message when this question is answered.

Submit

Advertising

Things Yous'll Need

• Ladder
• Screwdriver

• New chain

• Wire stripper
• Replacement switch
• Twist-on connectors

Cheers for submitting a tip for review!

• Disconnect the electricity past turning off the ability earlier treatment the ceiling fan.

Advertisement

About This Article

Article Summary 10

To replace a ceiling fan pull switch, you'll need to remove the old switch, detach the wires, and attach a new switch straight to the terminals. To start, turn off the circuit breaker that leads to your fan, and so you don't adventure electrocuting yourself. So, remove the cover on the fan and unscrew the nut on the outside of the pull switch, so you lot tin can pull it out. Make certain you write down the colors of each wire and which terminals they connect to, since you'll need this data later. Once you lot've removed the pull switch, take information technology to a dwelling house improvement shop, and buy a new one. The new switch should be identical in size, number of speeds, and wattage, or else it won't be compatible. When you attach the new switch, refer to your notes so you can connect the colored wires to the appropriate terminals. Once they're fastened, screw the nuts dorsum in, replace the fan embrace, and flip the excursion breaker back on. To learn how to attach a new switch using wire nuts, read on!

Did this summary help yous?

Thanks to all authors for creating a page that has been read 382,356 times.

Did this article assistance you?

Source: https://www.wikihow.com/Replace-a-Ceiling-Fan-Pull-Chain-Switch

Posted by: marksidest.blogspot.com

Share this post